Category:Modifications
From RigidWiki
Attention!
This page is ONLY for mainstream or BETA upgrades. If you have an upgrade proposal please add it to
Associated firmware modifications are in Changes for Firmware Upgrades
Contents
Safety
Title | Description | Picture | Tag |
---|---|---|---|
Emergency Button | Instantly turns everything off. | ||
Smoke Detector | Alerts you if there is a fire |
Full List Of Available Parts from Reliabuild3d.com
A full list of every available part for replacements | Use coupon 4e3d20 for 20% Off |
Main board, wiring etc.
Title | Description | Picture | Tag |
---|---|---|---|
RB1 Full Upgrade Kit with everything including new board and PS, cables, plates, extruder upgrades, etc. | http://reliabuild3d.com/product/rigidbot-1-electronics-upgrade-kit/ | Use coupon 4e3d20 for 20% Off | |
RBB Full Upgrade Kit with everything including new board and PS, cables, plates, extruder upgrades, etc. | http://reliabuild3d.com/product/reliabuild-full-electronics-upgrade-kit-rbb/ | Use coupon 4e3d20 for 20% Off | |
Basic Upgrade Kit including new board and PS, cables, etc.(RB1 and RBB) | http://reliabuild3d.com/product/basic-reliabuild-electronics-upgrade-kit/]] | Use coupon 4e3d20 for 20% Off | |
Control board alternatives | Replace original board with alternative. | |
|
Main PCB Support | No board flexing when attaching cables. | ![]() |
|
Stock Wiring Prep for Aftermarket Controller Board | Modify Stock wiring for use with aftermarket board without a need for adapters. | ![]() |
|
BYEBYE Board | Allow 3rd party control board connection to proprietary RigidBot cables. | |
|
Shorten Wires | Wires will not hang loose. | ||
LCD Smart Controller | Autonomous print controller with LCD and SD Card reader. | |
|
Replace Ribbon Cables | More fault tolerant cables. | ||
Replacing the Power Supply | Needed for custom control boards or faulted original PSU. | |
|
Quieting the Power Supply Fan | Less noise from PSU fan. | ![]() |
|
Replacing RB board with MKS 1.3 and ByeBye board | Replacing RB board | ![]() |
|
Z-Axis Stepper Motor - Series Connected Splitter Board | Split a single z-axis driver to power two z-axis stepper motors in series. | |
Title | Description | Picture | Tag |
---|---|---|---|
Pulley Upgrade - 36 to 16 teeth | Increase resolution on X and Y axis | ![]() |
|
Threaded Z rod | Quality improvement on Z axis | ![]() |
|
Z endstop adjustment screw | Tune Z endstop position without leveling HB | |
|
Idler Upgrade | Decrease friction and increase speed on X and Y axis | ![]() |
|
Adjustable Idler Upgrade | Smooth running idler with adjustable belt tension | |
|
Linear Bearing Mount | Stainless Linear Bearing Mount | ![]() |
|
Stepper Motor Bracket | Stainless Stepper Motor Bracket | |
|
Change 22mm Idler bearing to 10mm | Change 22mm Idler bearing to 10mm | |
Hardware
Title | Description | Picture | Tag |
---|---|---|---|
Cable Routing Clips | Wires will not break loose | ![]() |
|
Vibration reduction feet | Reduces vibration thus improving prints | ![]() |
|
LCD Angle Mount | Angles the LCD panel upward for better viewing | ![]() |
HotBed
Title | Description | Picture | Tag |
---|---|---|---|
Glass Bed Plate | Smoother surface then aluminium. No spikes or drops in temperature. | ![]() |
|
Flat leveling screws | Lower risk of nozzle damage. Easier to apply printing surface. | ![]() |
|
Silicon pad insulation for Glas Bed Plate | More efficient Hot Bed heating | ![]() |
|
Heated Bed - Replacing the connector | Make your heated bed safer | ![]() |
|
Preparing Heated Bed for PLA using PVA glue | Adhension for PLA | |
Extruder
Title | Description | Picture | Tag |
---|---|---|---|
Direct Extruders | Standard one. | ![]() |
|
Bowden Extruders |
|
![]() |
|
Extruder Cable Management | Extruder cables will not hang loose. | ![]() |
|
Cooling Fan Mount | Cool air keeps prints from warping. | ![]() |
|
Extruder Cable Strain Relief | Extruder cables will not hang loose. | ![]() |
|
Extruder's PCB 90 degrees rotation adapter | Ribbon cable will flex across and not along its edges. | ![]() |
|
Quieting the Extruder Fan | Less noise from fan. | ||
Dual V6 Mk8 Alloy Mount Kit | A third party Dual Extruder Mount designed around the pedigree E3D-V6 all metal hot ends, Mk8 drive gear and incorporating on-board Inductive Proximity Sensor circuitry. | |
|
Dual V6 Mk8 Alloy Mount Kit V2 | The second iteration of the Dual Extruder Mount designed around the pedigree E3D-V6 all metal hot ends, Mk8 drive gear and incorporating on-board Inductive Proximity Sensor circuitry. | |
|
Single V6 Mk8 Alloy Mount Kit | A third party Single Extruder Mount designed around the pedigree E3D-V6 all metal hot ends, Mk8 drive gear and incorporating on-board Inductive Proximity Sensor circuitry. | |
|
Diamond Hotend Mount | RB Mount and Plate for the Diamond Hotend, a 3x feed single nozzle extruder. | ![]() |
|
Proximity Sensor | Information and setup/troubleshooting for both the Inductive and Capacitive Proximity Sensor Switch | ![]() |
|
Hotend Comparison | Comparison of all of the available (hopefully) extruder upgrades in a easy to read list |
Spool and filament
Title | Description | Picture | Tag |
---|---|---|---|
Filament Guide | Better printing of soft filaments | ![]() |
|
Spool Holders | Change spools by just lifting the bar | ![]() |
|
Spool insert | Center hole rolls and prevents them from popping into the hollow spool center. | ![]() |
Tools
Title | Description | Picture | Tag |
---|---|---|---|
Handy accessories. | Handy accessories. | ![]() |
|
RigidBot Tramming Jig | Quick tool to level the bed | ![]() |
Examples
Title | Description | Picture | Tag |
---|---|---|---|
Walter's Printer | Pictures and a list of modifications done to Walter's RigidBot | ![]() |
Pages in category "Modifications"
The following 19 pages are in this category, out of 19 total.
D
E |
HLMQR |
R cont.SUZ |